Purchase a Platinum E-Liquid Limited Gift Voucher

KangerTech ProTank

KangerTech ProTank
KangerTech ProTank KangerTech ProTank KangerTech ProTank KangerTech ProTank KangerTech ProTank
Product Code: Kanpro1
Reward Points: 100
Availability: Out Of Stock
Price: £14.99
Price in reward points: 2000
Qty:     - OR -   Add to Wish List
Add to Compare


The bottom coil Kanger Protank is a top of the line clearomizer made from the best materials available.  It offers the same great features and performance as other bottom coil clearomizers but with the introduction of a strong pyrex glass tank and solid stainless steel construction. The ProTank is 510 threaded and will work on a 510 threaded Mods without the need for an adapter, but it also comes with a matching ego cone cover for use with various eGo style batteries such as the eGo-T, eGo-C, and eGo-C Twist

Since the KangerTech Protank is made of steel and glass, it is perfect for use with abrasive liquids such as the cinnamon red hots and spearment flavored e-liquids that often cause problems by reacting with the plastics used in standard clearomizers.  

Also, the bottom feed design makes the Protank great for use with thicker liquids.  Since gravity helps keep the wick saturated thicker liquids (higher VG content) can be used without getting the dreaded dry/burnt hits that are common with many tanks.

Replacement Coil Heads for this product can be found here:  KangerTech Protank Coil Replacement Heads (5pk)

What You get With the Kanger ProTank Kit:

  • 1 x 2.5ml ProTank with clear pyrex glass tank.
  • 2 x 2.4 ohm head and wick assemblies
  • 1 x Matching eGo Thread Cover
  • Instruction card

How to Use your KangerTech Protank:

  • To fill, turn the tank upside down and remove the threaded end cap.  Fill the outer portion of the tank (avoid getting e-liquid into the center airflow tube).  Screw the head and wick assembly onto the threaded end cap tightly then screw the end cap onto the tank tightly.  You can now turn it rightside up and check for leaks before using.
  • Gurgling or Leaking can occur if liquid gets into the center airflow tube.  To clear this liquid and improve performance remove the tank from the battery and blow through the mouthpiece into a paper towel.  The excess liquid will come out of the threaded end of the device.  If this happens often you may need to check that all connections are screwed down tightly or replace the head and wick assembly with a new one.
  • The head and wick assembly will sometimes loosen itself when the threaded end cap is unscrewed.  Always check that it is screwed on tightly before replacing the threaded end cap.  Not doing so could result in a leaking or non-working device.
  • You should never run the tank completely dry.  Doing so could result in a burnt or damaged wick and can cause leaking.  Refill the tank when the liquid level reaches approximately 1/3 full
  • Replacement heads will be available for this product soon.  The lifespan of replacement heads can vary quite a bit, but following the above instructions will maximize the lifespan of the coil.
Recommended Voltage for varying resistance levels:
  • 1.7-1.9ohm  -  3.1-3.4V
  • 2.1-2.3ohm  -
  • 2.4-2.6ohm  -  3.9-4.2V
  • 2.6-3.0ohm  -  4.3-4.7V
*The above recommendations are merely a guideline.  Personal preference as well as specific set ups, hardware, liquids, etc. can have an effect on the proper Voltage to use.

Write a review

Your Name:

Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:

SSL Certificates